Photonics Handbook

Diffraction gratings are optical components with a periodic structure that separate light into beams traveling in predictable directions based on their wavelength. The grating acts as the dispersive...

Photonics is the study of light and other types of radiant energy whose quantum unit is the photon. The impact of photonics on research, technology, navigation, culture, astronomy, forensics, and...

Early fiber lasers were inefficient and limited to low powers, until more effective methods emerged to deliver the pump light into the cladding. Valentin Gapontsev, founder and CEO of IPG Photonics,...

Electrical engineers are very familiar with the effects of shot noise, thermal noise, flicker noise and crosstalk, and recognize how these effects can reduce the signal-to-noise ratio (SNR) in their...

Superresolution optical microscopy, for which the Nobel Prize was awarded to Eric Betzig, Stefan Hell, and William Moerner in 2014, has been one of the most momentous developments in the life...

There are three fundamental properties of light: intensity, wavelength, and polarization. Almost all cameras today are designed for monochrome or color imaging. A monochrome camera is used to measure...

The term fluorescence is often applied as a synonym for photoluminescence, although luminescence actually covers fluorescence and phosphorescence. Both of these terms describe the process of...

Many common spectroscopic measurements require the coordinated operation of a detection instrument and light source, as well as data acquisition and processing. Integration of individual components...

When evaluating the surface of a component, surface roughness can be assessed by eye or by rubbing it with a fingertip. Common expressions include “shiny,” “lusterless and...

As recently as five years ago, shopping for a microscope light source was fairly straightforward. For routine applications, it was tungsten halogen, typically 100 W, while for fluorescence, it was an...

Profiling beams under 10 µm in size is one of the more challenging beam profiling applications. There are numerous reasons for this, including the very small size. Focal plane arrays commonly...

Optical fibers are made from either glass or plastic. Most are roughly the diameter of a human hair, and they may be many miles long. Light is transmitted along the center of the fiber from one end...

Light is a versatile tool for investigating physical and chemical processes in nature. Any specific system being analyzed may, through the light it emits or reflects, communicate information about...

Laser development for the microscopy market continues to be driven by key trends in applications, which currently include superresolution techniques, multiphoton applications in optogenetics and...

Surface quality has become one of the most poorly understood specifications in the optics industry. A significant portion of the confusion stems from the two major competing (and largely...

In their earliest forms, UV bandpass filters that were optimized for wavelengths less than 400 nm, such as the Schott UG or the Hoya U-series, were constructed of absorbing compounds in glass. Such...

The wavelength range of commercially available LEDs with single-element output power of at least 5 mW is 275 to 950 nm. Each wavelength range is made from a specific semiconductor material family,...

An interferometer is an instrument that compares the position or surface structure of two objects. The basic two-beam division of amplitude interferometer components consists of a light source, a...

Over 60 years have passed since the first demonstration of a laser in 1960. After the initial spark of interest, lasers were for a while categorized as “a solution waiting for a problem,”...

The first high-reflectance mirror coatings for the UV and vacuum UV (VUV) were of the Al + MgF2 type produced in the late 1950s. Coatings of this design are still used today for multigas cavity...

An optical time-domain reflectometer sends short pulses of light into a fiber and measures its reflections as a function of time. The delay of these reflections to the detector as well as their...

The basic setup in laser perforation includes a pulsed laser, a lens and either a moving mirror, a rotating web or both. Each laser pulse creates a hole in the material. During the blank time in...

Charged-injection device imagers are metal-oxide semiconductor (MOS) detectors that can be fabricated using PMOS, NMOS and CMOS integrated circuit technology, and may be configured as a...

Excimers are pulsed gas lasers that deliver high output power and pulse energies in the ultraviolet and deep-ultraviolet wavelengths. This enables them to power applications that cannot be supported...

Since their invention in the late 1960s, charge-coupled devices, also called CCDs, have found widespread use in imaging applications. Electronic cameras based on CCD technology are used in...

Optical coatings are deposited as thin-film multilayers of a variety of materials using specific deposition techniques. Coatings are applied to optical components that are intended for use at...

Photonics Rules of Thumb Scientists and engineers tend to want to answer simple relational questions with a blackboard covered with equations, even when questioners just want a rough estimate to...

That portion of the spectrum that the eye can see — and its rainbow of colors — is rather small, covering approximately 360 to 830 nm. What colors we perceive depends on wavelength, while...

Hyperspectral imaging spectroscopy has developed dramatically from a large, complex, remote-sensing satellite- or aircraft-based system into a rugged, compact, economically priced imaging and...

If we were to estimate the output of a CCD or thermal camera, we would typically draw an image over the detectors, aligning the image with the detector axes. We show it this way because it’s...

Designing devices that incorporate ultrathin films is an important means of enhancing yields. However, characterizing ultrathin films provides a challenge for mainstream metrology tools such as...

Illumination design has developed rapidly to include not only automotive headlamps and street lamps, but also backlit displays, fluorescent panel lighting, light-emitting diode or laser sources, and...

Intensity and uniformity can be described using different physical attributes, which makes interpreting requirements somewhat confusing. This article intends to provide an explanation and serve as a...

A lens collects light from a point on an object and focuses it to a corresponding conjugate point on an image. Under most conditions, the lens fails at this task because of some error in the...

There is a growing market for imaging systems that provides an immediate, slow-motion view of a process that allows one to see events that happen too quickly for the human eye to perceive or...

Radiometry involves several activities. The two most common are the description and measurement of optical radiation, and, starting with the knowledge of some aspects of optical radiation at one...

Controlling and minimizing heat output is desirable in most lighting applications. For example, conventional incandescent light sources are very inefficient with only a small portion of the...

Applications facilitated by tunable lasers fall into two categories: situations in which one or more discrete wavelengths are not available from any single- or multiline fixed-wavelength laser, or...

The market for flat panel displays (FPDs) has undergone tremendous growth, driven mostly by increased demand for televisions, cell phones, computers, digital cameras and MP3 players. Similarly,...

All optical spectrometry techniques rely on the measurement of radiant power. The configuration of the instrument varies based on the measurement technique: absorption, emission, luminescence, or...

Images are produced by many means: cameras, x-ray machines, electron microscopes, radar and ultrasound. They are used in the entertainment, medical, scientific and business industries; for security...

Conditions on the factory floor and in industrial cleanrooms with high-capacity air filtration systems can hamper the use of interferometry. Another problem is the testing of large-aperture mirrors...

Reading and writing systems for polygonal scanners differ in the use of the scanner. However, many performance characteristics are similar for both. In writing applications, a light source, usually a...

Plate beamsplitters Plate beamsplitters consist of a thin plate of optical crown glass with a different type of coating deposited on each side. The first surface is coated with an all-dielectric...

Lenses come in a variety of shapes, sizes and materials. They can be made of a single piece of glass or have multiple elements; their surfaces can be spherical, aspheric or cylindrical; they can be...

For any discussion of laser beam diagnostics, it is first necessary to define some terms that characterize beam properties. Broad definitions can include measurements of laser energy or power,...

Unlike an edge emitter, a VCSEL has a maximum operating power that is not limited by catastrophic optical damage of the exit aperture because its aperture is larger and its PN junction does not...

Imaging has long been used in industrial processes to measure, monitor, control, or otherwise manage the production of goods. The challenge to the process designer is to develop a tool that captures...

There are three fundamentally different dispersive phenomena in optical fiber, of which polarization mode dispersion (PMD) is the most complex. In digital multimode fiber systems, a light pulse...

Laser diodes vary widely in their wavelengths, powers, spectra and beam quality. Yet they share two fundamental components with all other lasers: an optical amplifier and a resonator that confines...