3D-Printed Micro-Optic Enables Vortex Bessel Beam Generation

Researchers from Soreq Nuclear Research Center in Israel have shown that 3D laser printing can be used to fabricate a high-quality, complex polymer optical device directly on the end of an optical fiber. This type of micro-optical device — which has details smaller than the diameter of a human hair — could provide an extremely compact and inexpensive way to tailor light beams for a variety of applications.

“Communication technologies, the internet, and many other applications are based on optical fibers,” said research team leader Shlomi Lightman from Soreq Nuclear Research Center in Israel. “When light comes out of the fiber, large bulky optical elements are typically used to route it to the next location. Our approach minimizes both the size and cost for this process by integrating the routing process into the fiber itself.”

A scanning electron microscopy image of the high-quality, complex polymer optical device is shown. Fabricated directly on the end of an optical fiber, it includes both a parabolic lens for light collimation and a twisted axicon optic that twists the light. Courtesy of Shlomi Litman, Soreq Nuclear Research Center.

The entire fabrication process for the micro-optical device takes less than five minutes. The fiber, together with the micro-optical device, costs less than $100, about a tenth of what a standard microscope objective lens performing a similar function would cost.

“The ability to create a Bessel beam directly from an optical fiber could be used for particle manipulation or fiber-integrated stimulated emission depletion (STED) microscopy, a technique that produces super-resolution images,” Lightman said. “Our fabrication method could also be used to upgrade an inexpensive lens to a higher quality smart lens by printing a smart small structure on it.”

To create the tiny optical devices, the researchers used a fabrication technique called 3D direct laser printing. This uses a laser beam with femtosecond pulses to create two-photon absorption in a photosensitive optical material. Only the tiny volumes where two-photon absorption occurs turn solid, providing a way to create high-resolution 3D elements.

Although this 3D direct laser printing has been used for some time, it is difficult to get the scale and alignment correct when fabricating such small optics on a fiber tip.

The researchers created an optical measuring system to analyze the performance of beams shaped by the fabricated device. The beam showed very low diffraction and laser powers could reach close to 10 MW/cm² before damaging the fabricated micro-optical device. Courtesy of Shlomi Lightman, Soreq Nuclear Research Center.

“We were able to overcome this hurdle by performing highly accurate 2D and 3D simulations before we began the fabrication process,” Lightman said. “In addition, we had to carefully think about how to integrate the optical elements with each other and then align that with the fiber core.”

After careful planning based on the simulations, the researchers used a commercial 3D direct laser writing system and a high optical quality photosensitive polymer to print 110-micron-tall optical device 60 microns in diameter on the end of a single mode optical fiber. The device included both a parabolic lens for light collimation and a helical axicon lens to twist the light. This turned light exiting the fiber into a twisted Bessel beam.

To analyze the quality of the fabricated optical device, the researchers built an optical measuring system to capture the shaped beam propagating from the modified fiber. They observed very low diffraction in the beam, which means that it could be useful for applications such as STED microscopy and particle manipulation.

They also found that the laser power could reach close to 10 MW/cm² before damaging the fabricated micro-optical device. This showed that even though the device was made from polymer, which is more susceptible than glass to heat damage from high powers, it could still be used to produce relatively high laser power.

Now that the researchers have demonstrated that precise multi-element micro-optics can be created using this direct 3D laser printing method, they are experimenting with using hybrid photosensitive materials that contain a low percentage of polymer. These materials could make it possible to produce higher quality optics that also have a longer shelf life and are more resistant to high laser powers, compared to polymer materials.

The research was published in Optics Letters (www.doi.org/10.1364/OL.470924).