Definitions

A form of a stereoscopic microscope having paired objectives, prisms and eyepieces, and invented by H. Greenough.

A telescope with an ellipsoidal secondary concave mirror that reflects rays from a parabolic primary mirror through an opening in the center of the primary, where the image is viewed with an eyepiece.

The soft x-rays used in the industrial radiography of materials having too small a range of densities to produce an image with normal x-rays.

A GRIN (gradient index) lens is a type of optical lens that utilizes a gradient in refractive index across its volume rather than having a uniform refractive index like conventional lenses. This...

The process in the manufacture of an optical system that gives it the required geometric shape.

Machinery used to grind and finish a component, such as a lens or prism, to a desired precision. Usually such machines carry a cup-shaped or flat tool (lap) into close contact with the part. An...

A tool of cast iron or another suitable medium used with a slurry of silicon carbide, aluminum oxide or emery for grinding optical surfaces.

A method of determining the abrasion resistance of very hard materials by passing a weighted wiper blade across them in a sand-water slurry for a specified number of times.

A plate of glass in which a face has been frosted by grinding or etching. It diffuses light by scattering in directions close to the incoming beam, but the light falls off rapidly at larger angles...

Also known as ground level. The lowest energy level of an atom or atomic system. A material in the ground state is not capable of emitting optical radiation. All other states are called excited...

A term variously applied to remote sensing techniques that essentially refers to all parametric conditions that influence the sensor system; includes the quantitative reality that the sensor sees and...

For a given mode propagating in a medium of refractive index n, the velocity of light in vacuum c, divided by the group velocity of the mode. For a plane wave of wavelength l, it is related to the...

For a particular mode, the reciprocal of the rate of change of the phase constant with respect to angular frequency.

A photodiode that has been designed so that the bar of semiconductor material has a PN junction perpendicular to its length and an ohmic contact at each of its ends.

The light flash that occurs when an electrical field is applied to a phosphor already excited by ultraviolet radiation.

A factor derived by equating the incident light on the subject to the required incident light for suitable photography. The lamp-subject-distance then is multiplied by the aperture and solved in...

In an optical waveguide, a mode whose field decays monotonically in the transverse direction everywhere external to the core and which does not lose power to radiation. Also called bound mode.

In an optical waveguide, a ray that is completely confined to the core.

A wave in which energy is focused near a boundary separating materials having different properties. Propagation of the wave is in a direction parallel to the boundary.

A camera accurately aligned to a weapons system to provide a photographic record of system performance.

An optical device that permits the alignment of a gun, cannon or rocket launcher system with its target.

A gyroscope is a mechanical device consisting of a spinning disk or wheel mounted on a spinning axis in such a way that its orientation remains fixed regardless of any movement of its mounting...

A mount that uses a floating suspension and a motor-driven gyroscope to keep a motion picture or still camera at a set angle even though the camera is mounted in a place that subjects it to heavy...

Gyroscopy refers to the principles and applications of gyroscopes, devices that measure or maintain orientation based on the principles of angular momentum. Gyroscopes are essential in various...

With respect to waveguides, the continuous change in the direction of the axis of the wavelength, during which the axis is perpendicular to the direction of polarization.

A defect in the cleaved end face of an optical fiber, defined as multiple surface irregularities across the fiber surface. A less serious imperfection of the same nature is known as mist.

Also known as constant angle or constant deviation fringes. The interference fringes observed with dense flat plates near normal incidence. The fringes of the Fabry-Perot interferometer are Haidinger...

Triggering a laser at a predetermined time by pumping it to a level just below its threshold and then using an auxiliary source that quickly pumps it above threshold. Means of achieving it in laser...

1. In a cathode-ray tube, the glow surrounding a bright spot that appears on the fluorescent screen as the result of the screen's light being reflected by the front and rear surfaces of the tube's...

The term half bandwidth (HBW) generally refers to the width of a spectral band or frequency range at half of its maximum amplitude. It is commonly used in the context of signal processing, optics,...

A communications system that can transmit in only a single direction at a time. See duplex.

Describing a surface that is coated with a film of metal of such thickness that it transmits about one-half of the incident light and reflects about one-half.

Refers to half a wave cycle.

1. The value on either the leading or the trailing edge of a laser pulse at which the power is one-half of its maximum value. 2. The wavelength at which a filter is transmitting one-half of its peak...

A device for forming at least two adjacent areas of polarized light. The angle between the directions of vibration of the light waves in the two areas is generally small.

A semicircular, half-wave quartz plate between the polarizer and analyzer. It often is used in forming precision settings with a polariscope.

A plate of electro-optical material that serves to rotate the plane of polarization of a light beam.

That voltage required across a Pockels, Kerr or other electro-optic light modulator to retard one polarization electrical vector by one-half a wavelength relative to the other. It corresponds to a...

A plate containing a uniform pattern of transparent holes in an opaque background, the clear area being nearly equal to the opaque area. Used in the printing process.

The gray-colored tones halfway between shadows and highlights in a reproduced image.

In chemistry, a halide refers to a chemical compound containing one or more halogen atoms bonded to another element. The halogens are a group of elements in the periodic table that includes fluorine...

The development of a transverse electric field in a solid material when it carries an electric current and is placed in a magnetic field that is perpendicular to the current.

1. The faintly hued ring that is seen to surround a light source viewed through fog or light clouds. The size of scattering particles determines the size of the ring. 2. The ring surrounding a...

Any of the five elements astatine, chlorine, fluorine, bromine and iodine, grouped because their chemical properties are similar.

A halogen lamp, also known as a tungsten halogen, quartz-halogen, or quartz iodine lamp, is an incandescent lamp that uses a tungsten filament surrounded by a small amount of halogen gas, such as...

The line that divides the two half-images in a coincidence rangefinder. The two halves of the images formed by the two objectives of the instrument must be brought to a point where they coincide...

A device small enough to be held in a hand that uses a magnifying lens and a translucent back to permit the viewing of photographic transparencies.

Usually a dielectric coating on glass or plastic optics; a coating that is comparable in hardness to glass itself.

Text or images printed on paper or another tangible medium, as opposed to those viewed electronically on a cathode-ray-tube screen.

High-modulus elastic fibers that exhibit the following differences from conventional elastic fibers: Increasing temperature decreases recovery force (the fibers are enthalpic vs. conventionally...