Silicon IC Folds, Stretches

Integrating electronic materials with ultrathin plastic and rubber-like substrates has resulted in a new form of stretchable silicon integrated circuit (IC) that can be folded and compressed -- even while operating -- without a reduction in electrical performance.

The IC can also be wrapped around complex shapes such as spheres, body parts or aircraft wings, which could lead to their use in wearable systems for personal health monitoring and other biomedical devices, or systems to monitor structural properties in airplanes.

Mechanically stretchable, "wavy" silicon integrated circuit (IC) embedded in transparent rubber, in a highly twisted configuration. (Image courtesy Science/AAAS)

“The notion that silicon cannot be used in such applications because it is intrinsically brittle and rigid has been tossed out the window,” said John Rogers, a Founder Professor of Materials Science and Engineering at the University of Illinois (U of I). “Through carefully optimized mechanical layouts and structural configurations, we can use silicon in integrated circuits that are fully foldable and stretchable.”

In December 2005, Rogers and his U of I research group reported the development of a one-dimensional, stretchable form of single-crystal silicon with micron-sized, wave-like geometries. That configuration allows reversible stretching in one direction without significantly altering the electrical properties, but only at the level of individual material elements and devices.

Now, Rogers and collaborators at the U of I, Northwestern University, and the Institute of High Performance Computing in Singapore report an extension of this basic wavy concept to two dimensions, and at a much more sophisticated level to yield fully functional integrated circuit systems.

“We’ve gone way beyond just isolated material elements and individual devices to complete, fully integrated circuits in a manner that is applicable to systems with nearly arbitrary levels of complexity,” said Rogers, who also is a researcher at the Beckman Institute and at the university’s Frederick Seitz Materials Research Laboratory.

“The wavy concept now incorporates optimized mechanical designs and diverse sets of materials, all integrated together in systems that involve spatially varying thicknesses and material types,” he said. “The overall buckling process yields wavy shapes that vary from place to place on the integrated circuit, in a complex but theoretically predictable fashion.”

Mechanically stretchable, "wavy" silicon integrated circuit on a rubber substrate. (Photo courtesy John Rogers)

Achieving high degrees of mechanical flexibility, or foldability, is important to sustaining the wavy shapes, Rogers said. “The more robust the circuits are under bending, the more easily they will adopt the wavy shapes which, in turn, allow overall system stretchability. For this purpose, we use ultrathin circuit sheets designed to locate the most fragile materials in a neutral plane that minimizes their exposure to mechanical strains during bending.”

To create their fully stretchable ICs, the researchers begin by applying a sacrificial layer of polymer to a rigid carrier substrate. On top of the sacrificial layer they deposit a very thin plastic coating, which will support the IC. The circuit components are then crafted using conventional techniques for planar device fabrication, along with printing methods for integrating aligned arrays of nanoribbons of single-crystal silicon as the semiconductor. The combined thickness of the circuit elements and the plastic coating is about 50 times smaller than the diameter of a human hair.

Next, the polymer layer is washed away, and the plastic coating and IC are bonded to a piece of prestrained silicone rubber. Lastly, the strain is relieved, and as the rubber springs back to its initial shape, it applies compressive stresses to the circuit sheet. Those stresses spontaneously lead to a complex pattern of buckling, to create a geometry that then allows the circuit to be folded, or stretched, in different directions to conform to a variety of complex shapes or to accommodate mechanical deformations during use.

Circuit diagram (top frame) and optical images of a stretchable, "wavy" silicon ring oscillator circuit on a rubber substrate, in the "as fabricated" flat state (top micrograph) and in moderate and high states of biaxial compression (middle and bottom micrographs, respectively). (Image courtesy John Rogers)

The researchers constructed integrated circuits consisting of transistors, oscillators, logic gates and amplifiers. The circuits exhibited extreme levels of bendability and stretchability, with electronic properties comparable to those of similar circuits built on conventional silicon wafers.

The new design and construction strategies represent general and scalable routes to high-performance, foldable and stretchable electronic devices that can incorporate established, inorganic electronic materials whose fragile, brittle mechanical properties would otherwise preclude their use, the researchers report.

“We’re opening an engineering design space for electronics and optoelectronics that goes well beyond what planar configurations on semiconductor wafers can offer,” Rogers said.

Rogers is a corresponding author of a paper on the research accepted for publication in the journal Science and posted on its Science Express Web site.

The work was funded by the National Science Foundation and the US Department of Energy.

For more information, visit: www.uiuc.edu